Georgia-Pacific | Professional

enMotion® Impulse™ 10 Automated Towel Dispenser

INSTALLING THE DISPENSER

Congratulations on choosing to improve the hygiene and image of your washroom! With one simple hand motion, the enMotion® Impulse™ 10 Automated Touchless Towel Dispenser elevates the image of your facility, helps improve hygiene, increases operational efficiency, and helps you support the EPA's guidelines to reduce waste.

TOOLS AND SUPPLIES
  • Screwdriver
  • Power Drill
  • Pencil or Pen
  • Level (recommended)
  • 4 ea. #8 Screws and Wall Anchors
STEP 1 - UNPACKING THE DISPENSER

Open case and locate listed components:

  • enMotion® Impulse™ 10 Automated Towel Dispenser
  • Dispenser Key
  • 4 "D" Cell Alkaline Batteries
  • Instruction Guide
  • Lifetime Satisfaction Card

STEP 2 - ASSEMBLING THE DISPENSER

  1. Locate key on bottom of dispenser. Open dispenser.
  2. Load four "D" cell alkaline batteries into battery compartment. A red light appears when batteries are properly installed.
  3. Close dispenser. The red light will shut off.

STEP 3 - DETERMINING THE INSTALLATION LOCATION

When placing dispenser, allow at least 4" on all sides from the closest objects on the wall.

Note: Mounting should comply with ADA Guidelines. Compliance is the responsibility of the installer. See the following document for more information:

Georgia-Pacific Compliance Guide for Title III of the Americans with Disabilities Act (PDF: 6 pg / 713 KB)

enMotion Installation Support Determining Location
STEP 4 - MOUNTING THE DISPENSER
Installing enMotion without mounting brackets

Mounting the Dispenser Without Mounting Brackets

  1. Mark and drill screw holes. Install wall anchors.
  2. Align dispenser with screw holes. Check level of dispenser.
  3. Use four screws to secure dispenser to the wall.

Mounting the Dispenser With Mounting Brackets

Installing enMotion with mounting brackets
  1. Fit two 54019 mounting brackets together. (Brackets sold separately.)
  2. Mark and drill screw holes. Install wall anchors.
  3. Align combined bracket with screw holes.
  4. Fit dispenser on bracket. Lock into place by gently pulling downward. Listen for a click indicating dispenser is properly secured.
  5. To remove dispenser, locate flexible tabs on center of brackets. Push tabs inward and gently pull dispenser upward.

STEP 5 - ADJUSTING THE SETTINGS
Setting Controls

The enMotion® Impulse™ 10 dispenser's adjustable settings are located inside the dispenser on the lower right side.

  1. The "Adjustable Sheet Length" (ASL) system allows for adjustments in towel sheet length.

    The sheet lengths are:
    • "S" Short towel (maximum number of hand dries) - approximately 8"
    • "M" Medium towel (optimal hand dry capacity) - approximately 12"
    • "L" Long towel (largest available towel) - approximately 16"
    Note: The ASL System is pre-set at the "L" option. Set ASL to meet your needs.
  2. The "Adjustable Time Delay" (ATD) system allows towels to dispense at different time delay intervals after a towel is removed from the dispenser.

    Adjustable Time Delay settings are:
    • "S" Short Delay
    • "M" Medium Delay
    • "L" Long Delay
    Note: The ATD system is pre-set at the "M" option. Set ATD to meet your needs.
  3. The "Adjustable Sensor Range" (ASR) system allows for adjustment in sensor range to provide dependable dispensing.

    Adjustable Sensor Range settings are:
    • "S" Short Range
    • "M" Medium Range
    • "L" Long Range
    Note: The ASR system is pre-set at the "M" option. Set ASR to meet your needs.
  4. The "Dispense Mode" (DM) system allows for adjustment in how the towel is presented to the end user.

    Dispense Mode settings are:
    • "On Demand" The towel will feed from the dispenser after the end user has activated the sensor.
    • "Hanging Towel" The towel will always be showing. After tearing off a towel, another towel will present itself.
    Note: The DM system is pre-set at the "On Demand" option. Set DM to meet your needs.
STEP 6 - OPERATING THE DISPENSER
  1. Load enMotion® Towels (SKU# 89460 or 89490) using the illustrated instructions in Loading the Dispenser.
  2. Dispensing enMotion® Towels
    • Wave hand approximately 2" - 2.5" across front of dispenser. An enMotion® towel is automatically dispensed.
    • Once towel is dispensed, tear towel to dry hands. A second towel cannot be dispensed until the first towel is removed. After the towel is removed, a short delay will occur to avoid paper waste.
  3. Note: To adjust the delay, see Step 5 "Adjusting the Settings."

enMotion® dispensers are offered via a lease agreement through an authorized distributor.